Polymer Systems
Technology Limited

Advanced Engineering




Controlled Volatility Film Adhesive

  • Two-part film adhesive
  • Cures at room temperature or rapidly with heat
  • Customer specifications only!
  • For electronic and space applications requiring low outgassing and minimal volatile condensables to avoid condensation in sensitive devices
  • For bonding or sealing silicone elastomers and some metals or plastics
  • For applications requiring shorter work times, easy clean-up, and consistent bond thickness
Typical PropertiesAverage Result
Appearance, Part A*Translucent
Appearance, Part B*Translucent
Dimensional Analysis*0.013 inches (0.3 mm)
Cured: 4 hours at 65°C (149°F)
Lap Shear Strength*250 psi (1.7 MPa)
Coefficient of Linear Thermal Expansion
above Tg (-25 to 250°C)465 ppm/°C (465µm/m/°C)
Collected Volatile Condensable Material (CVCM)*0.06%
Total Mass Loss (TML)*0.29%
Base Properties (material not in Film form):
Tensile Strength1,450 psi (10.0 MPa)
Tear Strength115 ppi (20.3 kN/m)
Young's Modulus315 psi (2.2 MPa)
Lap Shear Strength (primed w/ SP-270)250 psi (1.7 MPa)
After High Temperature Exposure:
7 days at 240°C (464°F)
Tensile Strength420 psi (2.9 MPa)
Tear Strength50 ppi (8.6 kN/m)
Young's Modulus150 psi (1.0 MPa)
Lap Shear Strength (primed w/ SP-270)200 psi (1.4 MPa)
10 cycles of 5 minutes at 300°C (572°C)
Tensile Strength1,400 psi (9.5 MPa)
Tear Strength110 ppi (19.2 kN/m)
Young's Modulus300 psi (2.1 MPa)
Lap Shear Strength (primed w/ SP-270)300 psi (2.1 MPa)

*Properties tested on a lot-to-lot basis. Do not use the properties shown in this technical profile as a basis for preparing specifications. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.


12"x 12" Sheet Kit (0.011 kg)
(30.48 x 30.48 cm)
14" x 20' Roll (0.925 kg)
(35.56 x 609.6 cm)


12 Months

Product Profile - Full Details Product Profile
Safety Data Sheet Material Safety Data Sheet
Two-part film adhesive. For bonding or sealing silicone elastomers and some metals or plastics.
Two-part film adhesive. For bonding or sealing silicone elastomers and some metals or plastics.


The warranty period provided by Polymer systems Technology ltd (hereinafter “PST”) is from the date of shipment when stored below 40°C in original unopened containers. Unless PST provides a specific written warranty of fitness for a particular use, PST’s sole warranty is that the product will meet PST’s then current specification. PST specifically disclaims all other expressed or implied warranties, including, but not limited to, warranties of merchantability and fitness for use. The exclusive remedy and PST’s sole liability for Packaging Warranty 50 mL Side-by-Side Kit 200 mL Side-by-Side Kit 400 ml Side-by-Side Kit 2 Pint Kit (910 g) 2 Gallon Kit (7.28 kg) 10 Gallon Kit (36.4 kg), Inc. All rights reserved. Trademarks are owned by PST or its affiliates unless otherwise noted. breach of warranty is limited to refund of purchase price or replacement of any product shown to be other than as warranted. PST expressly disclaims any liability for incidental or consequential damages.



PST believes, to the best of its knowledge, that the information and data contained herein are accurate and reliable. The user is responsible to determine the material’s suitability and safety of use. NuSil Technology cannot know each application’s specific requirements and hereby notifies the user that it has not tested or determined this material’s suitability or safety for use in any application. The user is responsible to adequately test and determine the safety and suitability for their application and NuSil Technology makes no warranty concerning fitness for any use or purpose. PST has completed no testing to establish safety of use in any medical application. PST has tested this material only to determine if the product meets the applicable specifications. (Please contact PST for assistance and recommendations when establishing specifications.) When considering the use of PST products in a particular application, review the latest Material Safety Data Sheet and contact PST with any questions about product safety information. Do not use any chemical in a food, drug, cosmetic, or medical application or process until having determined the safety and legality of the use. The user is responsible to meet the requirements of the U.S. Food and Drug Administration (FDA) and any other regulatory agencies. Before handling any other materials mentioned in the text, the user is advised to obtain available product safety information and take the necessary steps to ensure safety of use.



PST disclaims any expressed or implied warranty against the infringement of any domestic or international patent/intellectual property right. PST does not warrant the use or sale of the products described herein will not infringe the claims of any domestic or international patent/intellectual property right covering the product itself, its use in combination with other products, or its use in the operation of any process.


Medical Silicones
Biomaterials - Medical Silicones for Healthcare

Advanced Technologies

Advanced Technologies Industrial & Engineering Silicones
Space - Aviation Grade Industrial & Engineering Silicones


Food Medical Industrial Grade Silicone Tubing
Food, Medical & Industrial Quality Silicone Tubing


Silicone Mixing Dispensing Degassing Equipment
Mixing Dispensing & Degassing Equipment for Silicone