Polymer Systems
Technology Limited

Biomaterials

General Healthcare

Adhesives

MED-1000 » Silicone Adhesive

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Extrusion Rate†	2.5 g/minute
Tack-Free Time	12 minutes
Cured: 72 hours minimum at ambient temperature and humidity
Specific Gravity	1.08
Durometer, Type A	25
Tensile Strength	1,400 psi (9.7 MPa)
Elongation	795%
Tear Strength	75 ppi (13.2 kN/m)
Stress at 200% Strain	110 psi (0.76 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

† Performed using a Semco model 250-A pneumatic gun with a 14 gauge nozzle orifice and 90 ± 5 psi air pressure.

Full details » MED-1000 Product Profile

MED-1011 » Silicone Adhesive

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Tack-Free Time	13 minutes
Cured: 72 hours minimum at ambient temperature and humidity
Specific Gravity	1.12
Durometer, Type A	25
Tensile Strength	1,400 psi (9.7 MPa)
Elongation	725%
Tear Strength	100 ppi (17.6 kN/m)
Stress at 200% Strain	115 psi (0.79 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-1011 Product Profile

MED-1031 » Silicone Adhesive

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Extrusion Rate†	70 g/minute
Tack-Free Time	22 minutes
Cured: 7 days minimum at ambient temperature and humidity
Specific Gravity	1.1
Durometer, Type A	35
Tensile Strength	840 psi (5.8 MPa)
Elongation	310%
Tear Strength	40 ppi (7.1 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

†(Performed using a SEMCO® 440 nozzle with a ⅛" orifice and 90± 5 psi air pressure)

Full details » MED-1031 Product Profile

MED-1037 » Silicone Adhesive

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Flow Rate	.20 inches
Extrusion Rate†	2.8 g/minute
Tack-Free Time	9 minutes
Cured: 72 hours minimum at ambient temperature and humidity
Specific Gravity	1.07
Durometer, Type A	30
Tensile Strength	730 psi (5.0 MPa)
Elongation	565%
Stress at 200% Strain	170 psi (1.2 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

p>† Performed using a Semco model 250-A pneumatic gun with a 14 gauge nozzle orifice and 90 ± 5 psi air pressure.

Full details » MED-1037 Product Profile

MED-1040 » Rtv Silicone Adhesive

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Flow Rate (30 seconds)	2.2 inches
Tack-Free Time	9.5 minutes
Cured: 72 hours minimum at ambient temperature and humidity
Specific Gravity	1.03
Durometer, Type A	23
Tensile Strength	265 psi (1.83 MPa)
Elongation	340%
Tear Strength	17 ppi (3 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-1040 Product Profile

MED-1353 » Pressure Sensitive Silicone Adhesive

PROPERTIES
Typical Properties	Average Result
Uncured:
Viscosity	3.500 cP (3.500 mPas)
Appearance	Translucent
Non-Volatile Content	68%
Tack Test	2.8 lbs (12.2 N)
Cured: 24 hours minimum at ambient temperature and humidity. 15 minutes at 150°C (302°F)
180° Peel Strength	5.0 ppi (0.9 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-1353 Product Profile

MED-1356 » Pressure Sensitive Silicone Adhesive

PROPERTIES
Typical Properties	Average Result
Uncured:
Viscosity	1,750 cP (1,750 mPas)
Appearance	Translucent
Non-Volatile Content	65%
Tack Test	2.3 lbs (10.3 N)
Cured: 30 minutes at 70°C (158°F)
180° Peel Strength	3.0 ppi (0.5 kN/m)
Cured: 24 hours minimum at ambient temperature and humidity. 15 minutes at 150°C (302°F)
Tissue Culture (Cytotoxicity Testing)	Pass

# Also see: MED1-1356 for even better adhesion

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-1356 Product Profile

MED-6342 » Tacky Silicone Gel

NuSil Technology's MED-6342 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Work time	2 hours
Cured: 45 minutes at 135°C (275°F)
Penetration (62.4g cone, 60 seconds)	12 mm
Surface - Tack Test	10.0 psi
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-6342 Product Profile

MED-6345 » Tacky Silicone Gel

NuSil Technology's MED-6345 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Viscosity	16,000 cP (16,000 mPas)
Appearance	Translucent
Work Time	30 minutes
Cured: 3 hours at 60°C (140°F)
Penetration (62.4g cone, 60 seconds)	16.5 mm
Surface - Tack Test	5.0 psi
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-6345 Product Profile

MED-6346 » Silicone Gel

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Viscosity	7000 cP (7000 mPas)
Cure Time	5 minutes
Cured: 2 hours at 60°C
Surface-Tack Test	8 psi (0.06 MPa)
Penetration (¼" / 19.5 g for 5 seconds)	5.5 mm
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-6346 Product Profile

MED-6350 » Tacky Silicone Gel

NuSil Technology's MED-6350 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Viscosity	23,000 cP (23,000 mPas)
Appearance	Translucent
Work Time	2.5 hours
Cured: 30 minutes at 100°C (212°F)
Penetration (62.4g cone, 60 seconds)	13.9 mm
Surface - Tack Test	6.5 psi
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-6350 Product Profile

MED-6360 » Soft Silicone Adhesive

NuSil Technology's MED-6350 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Viscosity	465 cP (465 mPas)
Appearance	Translucent
Work Time	1 hour
Cured: 60 minutes at 140°C (284°F)
Penetration (62.4g cone, 60 seconds)	12 mm
Surface - Tack Test	12.0 psi
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-6360 Product Profile

MED-6362 » Soft Silicone Adhesive

NuSil Technology's MED-6362 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Viscosity	8,500 cP (8,800 mPas)
Appearance	Translucent
Work Time	1 hour
Cured: 60 minutes at 140°C (284°F)
Penetration (62.4g cone, 60 seconds)	13 mm
Surface - Tack Test	9.0 psi
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-6362 Product Profile

MED1-1356 » Pressure Sensitive Silicone Adhesive

PROPERTIES
Typical Properties	Average Result
Uncured:
Viscosity	300 cP (300 mPas)
Appearance	Translucent
Non-Volatile Content	50%
Tack Test	1.7 lbs (7.5 N)
Cured: 30 minutes at 70°C (158°F)
180° Peel Strength	3.75 ppi (0.7 kN/m)
Cured: 24 hours minimum at ambient temperature and humidity. 15 minutes at 150°C (302°F)
Tissue Culture (Cytotoxicity Testing)	Pass

# Also see: MED-1356

The test data shown for this material is the average value for typical properties. All of these properties may not be tested on a lot to lot basis and cannot be used to draft specifications. Please contact NuSil for assistance and recommendations in establishing limits for product specifications.

Full details » MED1-1356 Product Profile

MED1-4013 » Fast-Cure Silicone Adhesives

PROPERTIES
Typical Properties	Result	Metric Conv.
Uncured:
Appearance	Translucent	-
Viscosity, Part A	80,000 cP	80,000 mPas
Work Time, MED1-4013	15 minutes	-
Work Time, MED2-4013	15 hours minimum	-
Work Time, MED3-4013	60 minutes minimum	-
Cured: 24 hours at 25°C (MED1-4013 & MED3-4013)
Cured: 15 minutes at 150°C (MED2-4013)
Specific Gravity	1.12	-
Durometer, Type A, MED1-4013, MED3-4013	20	-
Durometer, Type A, MED2-4013	15	-
Tensile Strength	1,000 psi	6.9 Mpa
Elongation	800%	-
Tear Strength	130	23.0 kN/m

Full details » MED1-4013 Product Profile

MED2-4013 » Fast-Cure Silicone Adhesives

PROPERTIES
Typical Properties	Result	Metric Conv.
Uncured:
Appearance	Translucent	-
Viscosity, Part A	80,000 cP	80,000 mPas
Work Time, MED1-4013	15 minutes	-
Work Time, MED2-4013	15 hours minimum	-
Work Time, MED3-4013	60 minutes minimum	-
Cured: 24 hours at 25°C (MED1-4013 & MED3-4013)
Cured: 15 minutes at 150°C (MED2-4013)
Specific Gravity	1.12	-
Durometer, Type A, MED1-4013, MED3-4013	20	-
Durometer, Type A, MED2-4013	15	-
Tensile Strength	1,000 psi	6.9 Mpa
Elongation	800%	-
Tear Strength	130	23.0 kN/m

Full details » MED2-4013 Product Profile

MED3-4013 » Fast-Cure Silicone Adhesives

PROPERTIES
Typical Properties	Result	Metric Conv.
Uncured:
Appearance	Translucent	-
Viscosity, Part A	80,000 cP	80,000 mPas
Work Time, MED1-4013	15 minutes	-
Work Time, MED2-4013	15 hours minimum	-
Work Time, MED3-4013	60 minutes minimum	-
Cured: 24 hours at 25°C (MED1-4013 & MED3-4013)
Cured: 15 minutes at 150°C (MED2-4013)
Specific Gravity	1.12	-
Durometer, Type A, MED1-4013, MED3-4013	20	-
Durometer, Type A, MED2-4013	15	-
Tensile Strength	1,000 psi	6.9 Mpa
Elongation	800%	-
Tear Strength	130	23.0 kN/m

Full details » MED3-4013 Product Profile

Color Masterbatches

MED-4102 » OVERVIEW Color Masterbatch For High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Result
Appearance
MED-4102-1	White
MED-4102-2	Black
MED-4102-3	Red
MED-4102-4	Orange
MED-4102-5	Yellow
MED2-4102-6	Green
MED-4102-6	Dark Green
MED1-4102-7	Blue
MED-4102-7	Dark Blue
MED3-4102-8	Violet
Cytotoxicity (Mixed and cured with NuSil Technology MED series HCR)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4102 Product Profile

MED-4102-1 » Color Masterbatch For High Consistency Silicone Elastomer ‑ White

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	White
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4102-1 Product Profile

MED-4102-2 » Color Masterbatch For High Consistency Silicone Elastomer ‑ Black

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Black
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4102-2 Product Profile

MED-4102-3 » Color Masterbatch For High Consistency Silicone Elastomer ‑ Red

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Red
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4102-3 Product Profile

MED-4102-4 » Color Masterbatch For High Consistency Silicone Elastomer ‑ Orange

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Orange
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4102-4 Product Profile

MED-4102-5 » Color Masterbatch For High Consistency Silicone Elastomer ‑ Yellow

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Yellow
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4102-5 Product Profile

MED-4102-6 » Color Masterbatch For High Consistency Silicone Elastomer ‑ Dark Green

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Dark Green
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4102-6 Product Profile

MED-4102-7 » Color Masterbatch For High Consistency Silicone Elastomer ‑ Dark Blue

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Dark Blue
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4102-7 Product Profile

MED-4900 » OVERVIEW Color Masterbatch For Liquid Silicone Elastomer

PROPERTIES
Typical Properties	Result
Appearance
MED-4900-1	White
MED-4900-2	Black
MED-4900-3	Red
MED-4900-4	Orange
MED-4900-5	Yellow
MED2-4900-6	Green
MED-4900-6	Dark Green
MED1-4900-7	Blue
MED-4900-7	Dark Blue
MED3-4900-8	Violet
MED50-4900-1	Translucent White
MED50-4900-2	Translucent Black
MED50-4900-3	Translucent Red
MED50-4900-4	Translucent Orange
MED50-4900-5	Translucent Yellow
MED52-4900-6	Translucent Green
MED50-4900-6	Translucent Dark Green
MED51-4900-7	Translucent Blue
MED50-4900-7	Translucent Dark Blue
MED53-4900-8	Translucent Violet
Cytotoxicity (Mixed and cured with NuSil Technology MED series LSR)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4900 Product Profile

MED-4900-1 » Color Masterbatch For Liquid Silicone Elastomer ‑ White

NuSil Technology's MED-4900-1 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	White
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4900-1 Product Profile

MED-4900-2 » Color Masterbatch For Liquid Silicone Elastomer ‑ Black

NuSil Technology's MED-4900-2 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Black
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4900-2 Product Profile

MED-4900-3 » Color Masterbatch For Liquid Silicone Elastomer ‑ Red

NuSil Technology's MED-4900-3 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Red
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4900-3 Product Profile

MED-4900-4 » Color Masterbatch For Liquid Silicone Elastomer ‑ Orange

NuSil Technology's MED-4900-4 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Orange
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4900-4 Product Profile

MED-4900-5 » Color Masterbatch For Liquid Silicone Elastomer ‑ Yellow

NuSil Technology's MED-4900-5 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Yellow
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4900-5 Product Profile

MED-4900-6 » Color Masterbatch For Liquid Silicone Elastomer ‑ Dark Green

NuSil Technology's MED-4900-6 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Green
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4900-6 Product Profile

MED-4900-7 » Color Masterbatch For Liquid Silicone Elastomer ‑ Dark Blue

NuSil Technology's MED-4900-7 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Dark Blue
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4900-7 Product Profile

MED2-4102-6 » Color Masterbatch For High Consistency Silicone Elastomer ‑ Light Green

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Green
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED2-4102-6 Product Profile

MED2-4900 » Barium Sulfate Healthcare Silicone Color Masterbatch ‑ White

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	White
Non-Volatile Content	98.1%
Specific Gravity	1.55
Cured: 5 minutes at 150°C (302°F). Stabilize for 3 hours minimum at ambient temperature and humidity.
Tissue Culture (Cytotoxicity Testing)	Pass

Properties tested on a lot-to-lot basis. Do not use the properties shown in this technical profile as a basis for preparing specifications. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

For further information, please see Mixing Masterbatches
Guidelines for Mixing a Barium Sulfate Masterbatch Into a Silicone Product.

Full details » MED2-4900 Product Profile

MED2-4900-6 » Color Masterbatch For Liquid Silicone Elastomer ‑ Light Green

NuSil Technology's MED-4900-6 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Light Green
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED2-4900-6 Product Profile

MED3-4900 » Titanium Dioxide Healthcare Silicone Color Masterbatch ‑ White

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	White
Non-Volatile Content	99%
Specific Gravity	1.52
Cured: 5 minutes at 150°C (302°F). Stabilize for 3 hours minimum at ambient temperature and humidity.
Tissue Culture (Cytotoxicity Testing)	Pass

The above properties are tested on a lot-to-lot basis. Do not use as a basis for preparing specifications. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED3-4900 Product Profile

MED3-4900-8 » Color Masterbatch For Liquid Silicone Elastomer ‑ Violet

NuSil Technology's MED-4900-7 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Violet
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED3-4900-8 Product Profile

MED4-4900 » Ammonium Bicarbonate Healthcare Silicone Foam Color Masterbatch ‑ White

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	White
Cured: 10 minutes at 150°C (302°F). Stabilize for 3 hours minimum at ambient temperature and humidity.
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED4-4900 Product Profile

MED50-4900-1 » Color Masterbatches For Liquid Silicone Elastomer ‑ Translucent White

NuSil Technology's MED50-4900-1 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent White
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED50-4900-1 Product Profile

MED50-4900-2 » Color Masterbatches For Liquid Silicone Elastomer ‑ Translucent Black

NuSil Technology's MED50-4900-2 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent Black
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED50-4900-2 Product Profile

MED50-4900-3 » Color Masterbatches For Liquid Silicone Elastomer ‑ Translucent Red

NuSil Technology's MED50-4900-3 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent Red
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED50-4900-3 Product Profile

MED50-4900-4 » Color Masterbatches For Liquid Silicone Elastomer ‑ Translucent Orange

NuSil Technology's MED50-4900-4 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent Orange
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED50-4900-4 Product Profile

MED50-4900-5 » Color Masterbatches For Liquid Silicone Elastomer ‑ Translucent Yellow

NuSil Technology's MED50-4900-5 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent Yellow
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED50-4900-5 Product Profile

MED50-4900-6 » Color Masterbatches For Liquid Silicone Elastomer ‑ Translucent Dark Green

NuSil Technology's MED50-4900-6 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent Dark Green
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED50-4900-6 Product Profile

MED50-4900-7 » Color Masterbatches For Liquid Silicone Elastomer ‑ Translucent Dark Blue

NuSil Technology's MED50-4900-7 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent Dark Blue
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED50-4900-7 Product Profile

MED52-4900-6 » Color Masterbatches For Liquid Silicone Elastomer ‑ Translucent Light Green

NuSil Technology's MED50-4900-6 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent Light Green
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED52-4900-6 Product Profile

MED53-4900-7 » Color Masterbatches For Liquid Silicone Elastomer ‑ Translucent Violet

NuSil Technology's MED50-4900-7 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent Violet
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED53-4900-7 Product Profile

Dispersions

MED-2014 » Silicone Dispersion

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Non-Volatile Content	35%
Viscosity - (*reported value*)	1800 cps to 3700 cps
Cured: 60 minutes at 50°C; 60 minutes at 150°C; Stabilize 3 hours minimum at ambient temperature and humidity
Durometer, Type A	35
Tensile Strength	1,700 psi (11.72 MPa)
Elongation	900%
Tear Strength	160 ppi (33.6 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

Full details » MED-2014 Product Profile

MED-4159 » Silicone Dispersion

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Transparent
Non-Volatile Content	53%
Viscosity	185 cSt (159 mPas)
Cured: 7 days minimum at ambient temperature and humidity
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4159 Product Profile

MED-4162 » Silicone Dispersion

PROPERTIES
Typical Properties	Average Result
Appearance	Translucent
Non-Volatile Content	31%
Viscosity	30,000 cP (30,000 mPas)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4162 Product Profile

MED10-4161 » Silicone Dispersion

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Clear to amber
Non-Volatile Content	33%
Specific Gravity, Pycnometer	0.86
Viscosity	150 cSt (129 mPas)
Cured: 5 days minimum at 25°C (77°F), 50% relative humidity
Durometer, Type 00	25
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED10-4161 Product Profile

MED10-6400 » Addition Cure Silicone Dispersion

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Non-Volatile Content	35%
Viscosity	800 cP (800 mPas)
Cured: 30 min at 25°C (77°F), 45 min at 75°C (167°F), and 135 min at 150°C (302°F)
Durometer, Type A	30
Tensile Strength	1,500 psi (10.3 MPa)
Elongation	800%
Tear Strength	150 ppi (26.5 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED10-6400 Product Profile

MED10-6600 » Addition Cure Silicone Dispersion

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Clear to translucent
Non-Volatile Content	35%
Viscosity	400 cP (400 mPas)
Cured: 30 minutes at 25°C (77°F), 45 min at 75°C (167°F), and 135 min at 150°C (302°F)
Durometer, Type A	25
Tensile Strength	1,200 psi (8.3 MPa)
Elongation	750%
Tear Strength	145 ppi (25.5 kN/m)
Stress at 300% Strain	325 psi (2.2 MPa)
Refractive Index	1.465
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED10-6600 Product Profile

MED10-6605 » Rtv Cure Silicone Dispersion

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Clear to Translucent
Non-Volatile Content	29%
Viscosity	700 cP (700 mPas)
Cured: 5 days (+4/-0) at ambient temperature and humidity
Durometer, Type A	25
Tensile Strength	1,500 psi (10.3 MPa)
Elongation	950%
Tear Strength	125 ppi (22.0 kN/m)
Stress at 200% Strain	105 psi (0.7 MPa)
Stress at 300% Strain	160 psi (1.1 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED10-6605 Product Profile

MED10-6607 » Rtv Silicone Dispersion

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Non-Volatile Content	35%
Viscosity	6,000 cP (6,000 mPas)
Cured: 7 days at minimum temperature and humidity
Specific Gravity	1.1
Durometer, Type A	40
Tensile Strength	1,200 psi (8.3 MPa)
Elongation	650%
Tear Strength	95 ppi (16.8 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED10-6607 Product Profile

MED10-6640 » Addition Cure High Strength Silicone Dispersion

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Transparent to translucent
Non-Volatile Content	20%
Viscosity	2,500 cP (2,500 mPas)
Cured: 30 minutes at ambient temperature and humidity, 45 minutes at 75°C (167°F), and 135 minutes at 150°C (302°F)
Refractive Index	1.41
Durometer, Type A	40
Tensile Strength	1,700 psi (11.7 MPa)
Elongation	1,000 %
Tear Strength	300 ppi (52.9 kN/m)
Stress at 100% Strain	150 psi (1.03 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED10-6640 Product Profile

MED10-6655 » Rtv Fluorosilicone Dispersion

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Opaque White
Non-Volatile Content	60%
Viscosity	700 cP (700 mPas)
Cured: 72 hours at ambient temp. and humidity
Appearance	Translucent
Durometer, Type A	35
Tensile Strength	775 psi (5.3 MPa)
Elongation	425%
Tear Strength	45 ppi (7.9 kN/m)

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED10-6655 Product Profile

MED10-6670 » Low Coefficient Of Friction Silicone Coating

PROPERTIES
Typical Properties	Average Result
Uncured:.
Appearance A	Translucent
Appearance B	Translucent to White
Zahn cup Viscosity, Cup #2	16 seconds
Percent Solids, Mixed	25%
Cured: 5 minutes minimum at ambient temperature and humidity, then 5 minutes at 150°C (302°F)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED10-6670 Product Profile

MED11-6604 » Rtv Silicone Dispersion

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Non-Volatile Content	50%
Viscosity	250 cP (250 mPas)
Cured: 24 hours at ambient temperature and humidity
Specific Gravity	0.99
Durometer, Type A	15
Tensile Strength	75 psi (0.5 MPa)
Elongation	375%
Tear Strength	15 ppi (2.6 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED11-6604 Product Profile

MED16-6606 » Rtv Silicone Dispersion

PROPERTIES
Typical Properties	Average Result
Uncured:
Viscosity	105 cP (105 mPas)
Appearance	Translucent
Non-Volatile Content	30%
Cured: 72 hours minimum at ambient temperature and humidity
Specific Gravity	30%
Durometer, Type A	20
Tensile Strength	1,240 psi (8.5 MPa)
Elongation	800%
Tear Strength	120 ppi (21.0 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

Full details » MED16-6606 Product Profile

Fluids

MED-361 » Silicone Fluid

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Transparent
Volatile Content	0.1%
Refractive Index	1.40
Specific Gravity	0.97
Intracutaneous Toxicity	Pass
Systemic Toxicity	Pass
Pyrogenicity	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-361 Product Profile

MED-400 » Silicone Fluid

PROPERTIES
Typical Properties	Average Result 350 Cp	Average Result 1,000 Cp	Average Result 12,500 Cp
Uncured:
Appearance	Transparent	Transparent	Transparent to Translucent
Volatile Content	0.3%	0.2%	0.1%
Specific Gravity, Hydrometer	1.25	1.27	1.30
Refractive Index	1.38	1.38	1.38
Tissue Culture (Cytotoxicity Testing)	Pass	Pass	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

NuSil® MED-400 may be considered for use in human implantation for a period of greater than 29 days.

Full details » MED-400 Product Profile

MED-420 » Silicone Fluid

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Volatile Content	<0.1%
Refractive Index	1.393
Specific Gravity, Hydrometer	1.03 - 1.06
Tissue Culture (Cytotoxicity Testing)	Pass

Full details » MED-420 Product Profile

MED-460 » Silicone Fluid

NuSil Technology's MED-460 may be considered for use in human implantation for a period of greater than 29 days

PROPERTIES
Typical Properties	Average Result 350 Cp	Average Result 1,000 Cp	Average Result 12,500 Cp
Uncured:
Appearance	Translucent	Translucent	Translucent
Volatile Content	<0.2 %	<0.2%	<0.3%
Refractive Index	1.382	1.382	1.383
Tissue Culture (Cytotoxicity Testing)	Pass	Pass	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-460 Product Profile

Greases

MED-6731 » High Consistency Fluorosilicone Grease

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	White to gray
Volatile Content	0.20%
Specific Gravity	1.20
Viscosity	2,070,000 cP (2,070,000 mPas)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

The properties listed above properties are tested on a lot-to-lot basis. Do not use as a basis for preparing specifications. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-6731 Product Profile

MED-9011 » Low Consistency Silicone Grease

PROPERTIES
Typical Properties	Average Result
Uncured:
Viscosity	95,000 cP (95,000 mPas)
Appearance	Translucent
Specific Gravity	1.00
Tissue Culture (Cytotoxicity Testing)	Pass

Full details » MED-9011 Product Profile

MED-9021 » Medium Consistency Silicone Grease

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	White
Volatile Content	0.60%
Specific Gravity	1.08
Viscosity	300,000 cP (300,000 mPas)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

Full details » MED-9021 Product Profile

MED-9031 » High Consistency Silicone Grease

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	White
Volatile Content	0.25%
Specific Gravity	1.11
Viscosity	900,000 cP (900,000 mPas)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

Full details » MED-9031 Product Profile

High Consistency Rubbers - Class VI Line

SIL2-5020 » Class VI Supported High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Work Time	8 hours
Cured: 15 minutes at 165°C (329°F)
Specific Gravity	1.11
Durometer (Type A)	21
Tensile Strength	1,620 psi (11.2 MPa)
Elongation	1,185%
Tear Strength	195 ppi (34.3 kN/m)
Stress at 200% Strain	65 psi (0.5 MPa)

Full details » SIL2-5020 Product Profile

SIL2-5030 » Class VI Supported High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Work Time	5 hours
Cured: 15 minutes at 165°C (329°F)
Specific Gravity	1.11
Durometer (Type A)	31
Tensile Strength	1,690 psi (11.7 MPa)
Elongation	1,140%
Tear Strength	215 ppi (37.8 kN/m)
Stress at 200% Strain	120 psi (0.8 MPa)

Full details » SIL2-5030 Product Profile

SIL2-5040 » Class VI Supported High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Work Time	4 hours
Cured: 15 minutes at 165°C (329°F)
Specific Gravity	1.15
Durometer (Type A)	39
Tensile Strength	1,510 psi (10.4 MPa)
Elongation	1,115%
Tear Strength	220 ppi (38.7 kN/m)
Stress at 200% Strain	140 psi (1.0 MPa)

Full details » SIL2-5040 Product Profile

SIL2-5050 » Class VI Supported High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Work Time	4 hours
Cured: 15 minutes at 165°C (329°F)
Specific Gravity	1.16
Durometer (Type A)	50
Tensile Strength	1,350 psi (9.3 MPa)
Elongation	940%
Tear Strength	245 ppi (43.1 kN/m)
Stress at 200% Strain	380 psi (2.6 MPa)

Full details » SIL2-5050 Product Profile

SIL2-5060 » Class VI Supported High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Work Time	11 hours
Cured: 15 minutes at 165°C (329°F)
Specific Gravity	1.19
Durometer (Type A)	60
Tensile Strength	1,295 psi (8.9 MPa)
Elongation	920%
Tear Strength	255 ppi (44.9 kN/m)
Stress at 200% Strain	380 psi (2.6 MPa)

Full details » SIL2-5060 Product Profile

SIL2-5070 » Class VI Supported High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Work Time	2 hours
Cured: 15 minutes at 165°C (329°F)
Post Cured: 2 hours at 150°C (302°F)
Specific Gravity	1.2
Durometer (Type A)	68
Tensile Strength	1,330 psi (9.2 MPa)
Elongation	855%
Tear Strength	260 ppi (45.8 kN/m)
Stress at 200% Strain	360 psi (2.5 MPa)

Full details » SIL2-5070 Product Profile

SIL2-5080 » Class VI Supported High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Work Time	>24 hours
Cured: 15 minutes at 165°C (329°F) Post Cured: 2 hours at 150°C (302°F)
Specific Gravity	1.2
Durometer (Type A)	80
Tensile Strength	1,140 psi (7.9 MPa)
Elongation	615%
Tear Strength	210 ppi (37.0 kN/m)
Stress at 200% Strain	460 psi (3.2 MPa)

Full details » SIL2-5080 Product Profile

High Consistency Silicone Elastomer

Ultra High Performance

MED-4027 » UHP High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Work Time (Pot Life) @ 25°C	2.5 hours
Cured: 10 minutes at 171°C (340°F). Stabilize for 24 hours minimum at ambient temperature and humidity.
Specific Gravity	1.11
Durometer, Type A	30
Tensile Strength	2,300 psi (15.9 MPa)
Elongation	1050%
Tear Strength	235 ppi (41.2 kN/m)
Stress at 200% Strain	100 psi (0.69 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4027 Product Profile

MED-4055 » UHP High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Plasticity, Part A	85 mils (2.2 mm)
Plasticity, Part B	75 mils (1.9 mm)
Work Time	2.5 hours
Cured: 10 minutes at 138°C (280°F)
Specific Gravity	1.14
Post-Cured: 4 hours at 177°C (351°F). Stabilize for 24 hours minimum at ambient temperature and humidity.
Durometer, Type A	55
Tensile Strength	1,655 psi (11.4 MPa)
Elongation	880%
Tear Strength	315 ppi (55.6 kN/m)
Stress at 200% Strain	490 psi (3.4 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4055 Product Profile

MED-4070 » UHP High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Plasticity, Part A	120 mils (3.0 mm)
Plasticity, Part B	110 mils (2.8 mm)
Work Time	2.0 hours
Cured: 10 minutes at 138°C (280°F)
Specific Gravity	1.19
Post-Cured: 4 hours at 177°C (351°F). Stabilize for 24 hours minimum at ambient temperature and humidity.
Durometer, Type A	70
Tensile Strength	1,430 psi (9.9 MPa)
Elongation	760%
Tear Strength	300 ppi (52.9 kN/m)
Stress at 200% Strain	595 psi (4.1 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4070 Product Profile

Peroxide Cure

MED-4120 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Plasticity	65 mils (1.7 mm)
Cured: 5 minutes at 116°C (241°F). Catalyzed with 1.0 pph of CAT-102 (Peroxide).
Specific Gravity	1.10
Post Cured: 2 hours at 177°C (351°F). Stabilize for 3 hours minimum at ambient temperature and humidity.
Durometer, Type A	30
Tensile Strength	1,300 psi (9.0 MPa)
Elongation	950%
Tear Strength	135 ppi (23.8 kN/m)
Stress at 200% Strain	100 psi (0.7 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4120 Product Profile

MED-4135 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Plasticity	70 mils (1.8 mm)
Cured: 5 minutes at 116°C (241°F). Catalyzed with 1 pph of CAT-1
Specific Gravity	1.10
Post Cured: 2 hours at 177°C (351°F). Stabilize for 3 hours minimu
Durometer, Type A	35
Tensile Strength	1,350 psi ( 9.3 MPa)
Elongation	800%
Tear Strength	130 ppi (22.9 kN/m)
Stress at 200% Strain	190 psi (1.3 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4135 Product Profile

MED-4150 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Plasticity	80 mils (2.0 mm)
Cured: 5 minutes at 116°C (241°F). Catalyzed with 1 pph of CAT-102 (Peroxide).
Specific Gravity	1.16
Post Cured: 2 hours at 177°C (350°F). Stabilize for 3 hours minimum at ambient temperature and humidity.
Durometer, Type A	50
Tensile Strength	1,400 psi (9.65 MPa)
Elongation	750%
Tear Strength	190 ppi (33.5 kN/m)
Stress at 200% Strain	250 psi (1.72 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4150 Product Profile

MED-4174 » Silicone Elastomer

PROPERTIES
Typical Properties	Result	Metric Conv.
Uncured:
Appearance	Translucent	-

Plasticity	110 mils	(2.78mm)
Cured: 5 minutes at 116°C (241°F). Catalyzed with 1.0 pph of CAT-102 (Peroxide).
Specific Gravity	1.15	-
Post Cured: 4 hours at 205°C (401°F). Stabilize for 3 hours minimum at ambient temperature and humidity
Durometer, Type A	50	-
Tensile Strength	1,300 psi	8.9 MPa
Elongation	750%	-
Tear Strength, Die B	225 ppi	39.7 kN/m
Stress at 200% Strain	325 psi	2.2 MPa

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4174 Product Profile

MED4-4115 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Plasticity	90 mils (2.3 mm)
Cured: 5 minutes at 116°C (241°F)
Specific Gravity	1.15
Post Cured: 2hours at 249°C (480°F). Stabilized for 3 hours minimum at ambient temperature and humidity.
Durometer, Type A	50
Tensile Strength	1,600 psi (11.3 Mpa)
Elongation	500%
Tear Strength	100 ppi (17.6 kN/m)
Stress at 200% Strain	400 psi (2.8 Mpa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemntal Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED4-4115 Product Profile

MED4-4116 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Plasticity	120 mils (3.0 mm)
Cured: 5 minutes at 116°C (241°F)
Specific Gravity	1.21
Post Cured: 2 hours at 249°C (480°F). Sta
Durometer, Type A	70
Tensile Strength	1,300 psi (9.0 MPa)
Elongation	450%
Tear Strength	125 ppi (22.0 kN/m)
Stress at 200% Strain	550 psi (3.8 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED4-4116 Product Profile

Platinum Cure

MED-4014 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Plasticity, Part A	60 mils (1.5 mm)
Plasticity, Part B	60 mils (1.5 mm)
Work Time	25 hours
Cured: 10 minutes at 116°C (241°F). Stabilize for 3 hours minimum at ambient temperature and humidity.
Specific Gravity	1.08
Durometer, Type A	15
Tensile Strength	700 psi (4.8 MPa)
Elongation	1,330%
Tear Strength	155 ppi (27.3 kN/m)
Stress at 200% Strain	40 psi (0.28 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4014 Product Profile

MED-4020 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Plasticity, Part A	65 mils (1.6 mm)
Plasticity, Part B	65 mils (1.6 mm)
Work Time	10.0 hours
Cured: 10 minutes at 116°C (241°F). Stabilize for 24 hours minimum at ambient temperature and humidity.
Specific Gravity	1.1
Durometer, Type A	25
Tensile Strength	1,400 psi (9.7 MPa)
Elongation	1,245%
Tear Strength	190 ppi (33.5 kN/m)
Stress at 200% Strain	75 psi (0.52 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4020 Product Profile

MED-4025 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Plasticity, Part A	75 mils (1.9 mm)
Plasticity, Part B	75 mils (1.9 mm)
Cured: 10 minutes at 171°C (340°F). Stabilize for 24 hours minimum at ambient temperature and humidity
Specific Gravity	1.11
Durometer, Type A	30
Tensile Strength	1,285 psi (8.9 MPa)
Elongation	890%
Tear Strength	130 ppi (22.9 kN/m)
Stress at 200% Strain	105 psi (0.72 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4025 Product Profile

MED-4035 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Plasticity, Part A	70 mils (1.8 mm)
Plasticity, Part B	70 mils (1.8 mm)
Work Time	2.0 hours
Cured: 10 minutes at 116°C (241°F). Stabilize for 24 hours minimum at ambient temperature and humidity.
Specific Gravity	1.11
Durometer, Type A	35
Tensile Strength	1,565 psi (10.8 MPa)
Elongation	1,055%
Tear Strength	195 ppi (34.4 kN/m)
Stress at 200% Strain	195 psi (1.3 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4035 Product Profile

MED-4050 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent gray
Plasticity, Part A	95 mils (2.4 mm)
Plasticity, Part B	90 mils (2.3 mm)
Work Time	3.5 hours
Cured: 10 minutes at 115°C (239°F). Stabilize for 3 hours minimum at ambient temperature and humidity.
Specific Gravity	1.16
Durometer, Type A	50
Tensile Strength	1,500 psi (10.3 MPa)
Elongation	985%
Tear Strength	265 ppi (46.7 kN/m)
Stress at 200% Strain	305 psi (2.1 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4050 Product Profile

MED-4065 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent tan
Plasticity, Part A	125 mils (3.2 mm)
Plasticity, Part B	110 mils (2.8 mm)
Work Time	6.0 hours
Cured: 10 minutes at 116°C (241°F). Stabilize for 24 hours minimum at ambient temperature and humidity.
Specific Gravity	1.2
Durometer, Type A	65
Tensile Strength	1,250 psi (8.6 MPa)
Elongation	1,000%
Tear Strength	265 ppi (46.7 kN/m)
Stress at 200% Strain	355 psi (2.4 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4065 Product Profile

MED-4080 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent tan
Plasticity, Part A	125 mils (3.2 mm)
Plasticity, Part B	100 mils (2.5 mm)
Work Time	8.0 hours
Cured: 10 minutes at 116°C (241°F). Stabilize for 24 hours minimum at ambient temperature and humidity.
Specific Gravity	1.2
Durometer, Type A	80
Tensile Strength	1,150 psi (7.9 MPa)
Elongation	735%
Tear Strength	225 ppi (39.7 kN/m)
Stress at 200% Strain	450 psi (3.1 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4080 Product Profile

VersaSil

MED-4032 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Versasil³ 30 Med-4032	Versasil³ 40 Med-4042	Versasil³ 50 Med-4052
Cured: 10 min. at 116°C (241°F)
Specific Gravity	1.1	1.11	1.16
Durometer, Type A	30	40	50
Tensile Strength	1,200 psi (8.3 MPa)	1,475 psi (10.2 MPa)	1,400 psi (9.7 MPa)
Elongation	1,100%	1,000%	1,100%
Tear Strength	160 ppi (28.2 kN/m)	160 ppi (28.2 kN/m)	230 ppi (40.6 kN/m)
Stress at 200% Strain	140 psi (1.0 MPa)	230 psi (1.6 MPa)	280 psi (1.9 MPa)
Tissue Culture (Cytotocixity Testing)	Pass	Pass	Pass
Elemental Analysis of Trace Metals	Pass	Pass	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4032 Product Profile

MED-4042 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Versasil³ 30 Med-4032	Versasil³ 40 Med-4042	Versasil³ 50 Med-4052
Cured: 10 min. at 116°C (241°F)
Specific Gravity	1.1	1.11	1.16
Durometer, Type A	30	40	50
Tensile Strength	1,200 psi (8.3 MPa)	1,475 psi (10.2 MPa)	1,400 psi (9.7 MPa)
Elongation	1,100%	1,000%	1,100%
Tear Strength	160 ppi (28.2 kN/m)	160 ppi (28.2 kN/m)	230 ppi (40.6 kN/m)
Stress at 200% Strain	140 psi (1.0 MPa)	230 psi (1.6 MPa)	280 psi (1.9 MPa)
Tissue Culture (Cytotocixity Testing)	Pass	Pass	Pass
Elemental Analysis of Trace Metals	Pass	Pass	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4042 Product Profile

MED-4052 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Versasil³ 30 Med-4032	Versasil³ 40 Med-4042	Versasil³ 50 Med-4052
Cured: 10 min. at 116°C (241°F)
Specific Gravity	1.1	1.11	1.16
Durometer, Type A	30	40	50
Tensile Strength	1,200 psi (8.3 MPa)	1,475 psi (10.2 MPa)	1,400 psi (9.7 MPa)
Elongation	1,100%	1,000%	1,100%
Tear Strength	160 ppi (28.2 kN/m)	160 ppi (28.2 kN/m)	230 ppi (40.6 kN/m)
Stress at 200% Strain	140 psi (1.0 MPa)	230 psi (1.6 MPa)	280 psi (1.9 MPa)
Tissue Culture (Cytotocixity Testing)	Pass	Pass	Pass
Elemental Analysis of Trace Metals	Pass	Pass	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4052 Product Profile

MED-4062 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Versasil³ 30 Med-4032	Versasil³ 40 Med-4042	Versasil³ 50 Med-4052	Versasil³ 50 Med-4062
Cured: 10 min. at 116°C (241°F)
Specific Gravity	1.1	1.11	1.16	1.16
Durometer, Type A	30	40	50	60
Tensile Strength	1,200 psi (8.3 MPa)	1,475 psi (10.2 MPa)	1,400 psi (9.7 MPa)	1,400 psi (9.7 MPa)
Elongation	1,100%	1,000%	1,100%	1,000%
Tear Strength	160 ppi (28.2 kN/m)	160 ppi (28.2 kN/m)	230 ppi (40.6 kN/m)	250 ppi (44.1 kN/m)
Stress at 200% Strain	140 psi (1.0 MPa)	230 psi (1.6 MPa)	280 psi (1.9 MPa)	300 psi (2.1 MPa)
Tissue Culture (Cytotocixity Testing)	Pass	Pass	Pass	Pass
Elemental Analysis of Trace Metals	Pass	Pass	Pass	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4062 Product Profile

MED-4072 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Versasil³ 30 Med-4032	Versasil³ 40 Med-4042	Versasil³ 50 Med-4052
Cured: 10 min. at 116°C (241°F)
Specific Gravity	1.1	1.11	1.16
Durometer, Type A	30	40	50
Tensile Strength	1,200 psi (8.3 MPa)	1,475 psi (10.2 MPa)	1,400 psi (9.7 MPa)
Elongation	1,100%	1,000%	1,100%
Tear Strength	160 ppi (28.2 kN/m)	160 ppi (28.2 kN/m)	230 ppi (40.6 kN/m)
Stress at 200% Strain	140 psi (1.0 MPa)	230 psi (1.6 MPa)	280 psi (1.9 MPa)
Tissue Culture (Cytotocixity Testing)	Pass	Pass	Pass
Elemental Analysis of Trace Metals	Pass	Pass	Pass
Cured: 10 min. at 116°C (241°F)
Specific Gravity	1.16	1.22	1.22
Durometer, Type A	60	70	80
Tensile Strength	1,400 psi (9.7 MPa)	1,100 psi (7.6 MPa)	1,150 psi (7.9 MPa)
Elongation	1,000%	875%	900%
Tear Strength	250 ppi (44.1 kN/m)	240 ppi (42.3 kN/m)	200 ppi (35.5 kN/m)
Stress at 200% Strain	300 psi (2.1 MPa)	450 psi (3.1 MPa)	400 psi (2.8MPa)
Tissue Culture (Cytotocixity Testing)	Pass	Pass	Pass
Elemental Analysis of Trace Metals	Pass	Pass	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4072 Product Profile

MED-4082 » High Consistency Silicone Elastomer

PROPERTIES
TYPICAL PROPERTIES	AVERAGE RESULT	STANDARD	NT-TM
Cured: 10 min. @ 116°C (241°F). Stabilize for 3 hours minimum at ambient temperature and humidity
Specific Gravity	1.22	ASTM D792	003
Durometer, Type A	80	ASTM D2240	006
Tensile Strength	1,150 psi (7.9 MPa)	ASTM D412	007
Elongation	900%	ASTM D412	007
Tear Strength	200 ppi (35.5 kN/m)	ASTM D624	009
Stress @ 200% Strain	400 psi (2.8MPa)	ASTM D412	007
Tissue Culture (Cytotoxicity Testing)	Pass	USP <87> ISO 10993-5	061
Elemental Analysis of Trace Metals	Pass	ASTM E305	131

The data above represents the properties of the product when cured using the Addition Cure System (CAT-40 and CAT-55).

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4082 Product Profile

Low Consistency Silicone Elastomers - Platinum Cure

MED-4011 » Low Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Viscosity, Part A	105,000 cP (105,000 mPas)
Viscosity, Part B	1,500 cP (1,500 mPas)
Cured: 3 minutes at 150°C (302°F)
Post-Cured: 1 hour at 150°C (302°F). Stabilize for 3 hours at ambient temperature and humidity
Specific Gravity	1.09
Durometer, Type A	27
Tensile Strength	670 psi (4.6 MPa)
Elongation	530%
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4011 Product Profile

MED-4044 » Low Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Viscosity, Part A	130,000 cP (130,000 mPas)
Viscosity, Part B	380 cP (380 mPas)
Work Time	5 hours
Cured: 5 minutes at 177°C (376°F)
Post-Cured: 1 hour at 150°C (328°F). Stabilize for 3 hours minimum at ambient temperature and humidity.
Specific Gravity	1.09
Durometer, Type A	40
Tensile Strength	875 psi (6.0 MPa)
Elongation	360%
Tear Strength	150 ppi (26.5 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4044 Product Profile

MED-4086 » Ultra-Soft Low Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Viscosity, Part A	8,300 cP (8,300 mPas)
Viscosity, Part B	4,600 cP (4,600 mPas)
Work Time	18 hours
Cured: 45 minutes at 150°C (302°F)
Durometer, Type 000	55
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4086 Product Profile

MED-4917 » Low Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Viscosity, Part A	14,000 cP (14,000 mPas)
Viscosity, Part B	9,500cP (9,500 mPas)
Work Time	31 hours
Cured: 30 minutes at 150°C (302°F)
Specific Gravity	1.06
Durometer, Type A	20
Tensile Strength	500 psi (3.4 MPa)
Elongation	385%
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4917 Product Profile

MED-6010 » Optically Clear Low Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Viscosity, Part A	19,000 cP (mPas)
Viscosity, Part B	13,000 cP (mPas)
Work Time	4 hours
Refractive Index	1.43
Cured: 30 minutes at 150°C (302°F)
Specific Gravity	1.05
Durometer, Type A	50
Tensile Strength	950 psi (6.5 MPa)
Elongation	140%
Tear Strength	30 ppi (5.3 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-6010 Product Profile

MED-6015 » Optically Clear Low Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Transparent
Viscosity, Part A	5,500 cP (5,500 mPas)
Viscosity, Part B	95 cP (95 mPas)
Work Time	5.5 hours
Cured: 15 minutes at 150°C (302°F)
Specific Gravity	1.03
Durometer, Type A	50
Tensile Strength	1,200 psi (8.2 MPa)
Elongation	100%
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-6015 Product Profile

MED-6019 » Optically Clear High Durometer Low Consistency Silicone Elastomers

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Transparent
Viscosity, Part A	28,000 cP (28,000 mPas)
Viscosity, Part B	23,000 cP (23,000 mPas)
Work Time	2.5 hours
Cured: 2 hours at 50°C (122°F)
Specific Gravity	1.07
Durometer, Type A	75
Tensile Strength	1,300 psi (9.0 MPa)
Elongation	65%
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-6019 Product Profile

MED-6020 » Optically Clear Low Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Transparent
Viscosity, Part A	76,000 cP (76,000 mPas)
Viscosity, Part B	54,000 cP (54,000 mPas)
Work Time	4 hours
Refractive Index	1.43
Cured: 30 minutes at 150°C (302°F)
Durometer, Type A	40
Tensile Strength	680 psi (4.7 MPa)
Elongation	215%
Tear Strength	40 ppi (7.5 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-6020 Product Profile

MED-6033 » Clear Low Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Transparent
Viscosity, Part A	84,000 cP (84,000 mPas)
Viscosity, Part B	60,000 cP (60,000 mPas)
Refractive Index, Part A	1.41
Refractive Index, Part B	1.41
Work Time	50 hours
Cured: 30 minutes at 150°C (302°C)
Specific Gravity	1.03
Durometer, Type A	50
Tensile Strength	730 psi (5.3 MPa)
Elongation	390%
Tear Strength	80 ppi (14.1 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-6033 Product Profile

MED2-4220 » Fast Cure Low Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Viscosity, Part A	22,000 cP (22,000 mPas)
Viscosity, Part B	17,000 cP (17,000 mPas)
Work Time	3 minutes
Cured: 15 minutes at 150°C (302°F)
Specific Gravity	1.07
Durometer, Type A	20
Tensile Strength	585 psi (4.4 MPa)
Elongation	500%
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

Full details » MED2-4220 Product Profile

MED3-4220 » Fast Cure Low Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Viscosity, Part A	84,000 cP (84,000 mPas)
Viscosity, Part B	65,000 cP (65,000 mPas)
Work Time	15 minutes
Cured: 30 minutes at 150°C (302°F)
Specific Gravity	1.11
Durometer, Type A	25
Tensile Strength	1,100 psi (7.6 MPa)
Elongation	624%
Tear Strength	74 ppi (13.5 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

Full details » MED3-4220 Product Profile

MED4-4220 » Low Consistency Silicone Elastomer

NuSil Technology's MED4-4220 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Viscosity, Part A	25,000 cP (25,000 mPas)
Viscosity, Part B	19,000 cP (19,000 mPas)
Work Time	27 minutes
Cured: 15 minutes at 150°C (302°F)
Durometer, Type A	17
Tensile Strength	660 psi (4.5 MPa)
Elongation	580%
Tear Strength	35 ppi (6.2 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED4-4220 Product Profile

Inks

MED-6608 » OVERVIEW Silicone Coating / Marking Ink Series

PROPERTIES
Typical Properties	Average Result	Metric Conv.
Uncured:
Viscosity	1,150 cP	1,150 mPas
Non-Volatile Content	70%	-
Tack-Free Time	45 minutes	-
Cured: 24 hours minimum at ambient temp. and humidity
Adhesion*	Pass	-
Cured: 7 days minimum at ambient temp. and humidity
Specific Gravity (white / black)	1.13 / 1.46	-
Cytotoxicity	Pass	-

Full details » MED-6608 Product Profile

MED-6608-1 » White Silicone Coating / Marking Ink Series

PROPERTIES
Typical Properties	Average Result	Metric Conv.
Uncured:
Viscosity	1,150 cP	1,150 mPas
Non-Volatile Content	70%	-
Tack-Free Time	45 minutes	-
Cured: 24 hours minimum at ambient temp. and humidity
Adhesion(Primed with MED-160)	Pass	-
Cured: 7 days minimum at ambient temp. and humidity
Specific Gravity (white / black)	1.13 / 1.46	-
Cytotoxicity	Pass	-

Full details » MED-6608-1 Product Profile

MED-6608-2 » Black Silicone Coating / Marking Ink Series

PROPERTIES
Typical Properties	Average Result	Metric Conv.
Appearance	Black
Viscosity	1,150 cP	1,150 mPas
Non-Volatile Content	70%	-
Tack-Free Time	80 minutes	-
Cured: 24 hours minimum at ambient temp. and humidity
Adhesion(Primed with MED-160)	Pass	-
Cured: 7 days minimum at ambient temp. and humidity
Specific Gravity	1.46	-
Cytotoxicity	Pass	-

Full details » MED-6608-2 Product Profile

MED-6613-1 » Silicone Ink (WHITE)

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	White
Non-Volatile Content, Part A	65%
Non-Volatile Content, Part B	65%
Cured: 5 minutes at 150°C (302°F)
Tissue Culture (Cytotoxicity Testing)	Pass

Full details » MED-6613-1 Product Profile

MED-6613-2 » Silicone Ink (BLACK)

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Black
Non-Volatile Content, Part A	60%
Non-Volatile Content, Part B	60%
Viscosity, Part A	900 cP (800 mPas)
Viscosity, Part B	800 cP (11,500 mPas)
Cured: 5 minutes at 150°C (302°F)
Adhesion	Pass
Cured: 30 minutes minimum at ambient temperature and humidity
Tissue Culture (Cytotoxicity Testing)	Pass

Full details » MED-6613-2 Product Profile

MED-6613-7 » Silicone Ink (DARK BLUE)

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Dark Blue
Non-Volatile Content, Part A	65%
Non-Volatile Content, Part B	65%
Cured: 5 minutes at 150°C (302°F)
Tissue Culture (Cytotoxicity Testing)	Pass

Full details » MED-6613-7 Product Profile

MED8-6608-2 » Black Silicone Coating / Marking Ink

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Black
Non-Volatile Content	70%
Viscosity	800 cP (800 mPas)
Tack-Free Time	40 minutes
Cured: 7 days minimum at ambient temperature and humidity.
Specific Gravity	1.83
Tissue Culture (Cytotoxicity Testing)	Pass

Full details » MED8-6608-2 Product Profile

Liquid Silicone Rubbers

MED-4901 » Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Work Time	25 hours
Cured: 5 minutes at 150°C (302°F).
Specific Gravity	1.1
Durometer, Type 00	40
Tensile Strength	285 psi (2.0 MPa)
Elongation	1135%
Tear Strength	55 ppi (9.7 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4901 Product Profile

MED-4905 » Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Work Time	55 hours
Cured: 5 minutes at 150°C (302°F). Stabilize for 3 hours minimum at ambient temperature and humidity.
Durometer, Type A	7
Tensile Strength	350 psi (2.4 MPa)
Elongation	1000%
Tear Strength	70 ppi (12.3 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4905 Product Profile

MED-4910 » Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Extrusion Rate†, Part A	85 g/min
Extrusion Rate†, Part B	110 g/min
Work Time	70 hours
Cured: 5 minutes at 150 °C (302°F). Stabilize for 3 hours minimum at ambient temperature and humidity
Specific Gravity	1.07
Durometer, Type A	10
Tensile Strength	450 psi (3.1 MPa)
Elongation	1000%
Tear Strength	65 ppi (11.5 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

†(Performed using a SEMCO® model 250-A pneumatic gun with a ⅛ nozzle orifice and 90± 5 psi air pressure)

Full details » MED-4910 Product Profile

MED-4920 » Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Extrusion Rate†, Part A	65 g/min
Extrusion Rate†, Part B	90 g/min
Work Time	>72 hours
Cured: 5 minutes at 150 °C (302°F). Stabilize for 3 hours minimum at ambient temperature and humidity
Specific Gravity	1.14
Durometer, Type A	20
Tensile Strength	750 psi (5.2 MPa)
Elongation	700%
Tear Strength	125 ppi (22.0 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

†(Performed using a SEMCO® model 250-A pneumatic gun with a ⅛ nozzle orifice and 90± 5 psi air pressure)

Full details » MED-4920 Product Profile

MED-4930 » Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Extrusion Rate†, Part A	155 g/min
Extrusion Rate†, Part B	190 g/min
Work Time	>72 hours
Cured: 5 minutes at 150 °C (302°F). Stabilize for 3 hours minimum at ambient temperature and humidity
Specific Gravity	1.13
Durometer, Type A	30
Tensile Strength	1350 psi (9.3 MPa)
Elongation	730%
Tear Strength	150 ppi (26.3 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

†(Performed using a SEMCO® model 250-A pneumatic gun with a ⅛ nozzle orifice and 90± 5 psi air pressure)

Full details » MED-4930 Product Profile

MED-4940 » Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Extrusion Rate†, Part A	210 g/min
Extrusion Rate†, Part B	235 g/min
Work Time	>72 hours
Cured: 5 minutes at 150 °C (302°F). Stabilize for 3 hours minimum at ambient temperature and humidity.
Specific Gravity	1.12
Durometer, Type A	40
Tensile Strength	1190 psi (8.2 MPa)
Elongation	560%
Tear Strength	246 ppi (43.4 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

†(Performed using a SEMCO® model 250-A pneumatic gun with a ⅛ nozzle orifice and 90± 5 psi air pressure)

Full details » MED-4940 Product Profile

MED-4950 » Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Extrusion Rate†, Part A	95 g/min
Extrusion Rate†, Part B	100 g/min
Work Time	>72 hours
Cured: 5 minutes at 150°C (302°C). Stabilize for 3 hours minimum at ambient temperature and humidity
Specific Gravity	1.14
Durometer, Type A	50
Tensile Strength	1,445 psi (9.9 MPa)
Elongation	700%
Tear Strength	243 ppi (42.9 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

†(Performed using a SEMCO® model 250-A pneumatic gun with a ⅛ nozzle orifice and 90± 5 psi air pressure)

Full details » MED-4950 Product Profile

MED-4960 » Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Extrusion Rate†, Part A	65 g/min
Extrusion Rate†, Part B	105 g/min
Work Time	>24 hours
Cured: 5 minutes at 165°C (329°F)
Specific Gravity	1.15
Durometer, Type A	60
Tensile Strength	1,300 psi (9.0 MPa)
Elongation	525%
Tear Strength	250 ppi (44.1 kN/m)
Stress at 200% Strain	600 psi (4.1 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

†(Performed using a SEMCO® model 250-A pneumatic gun with a ⅛ nozzle orifice and 90± 5 psi air pressure)

Full details » MED-4960 Product Profile

MED-4970 » Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Extrusion Rate†, Part A	32 g/min
Extrusion Rate†, Part B	50 g/min
Work Time	>72 hours
Cured: 5 minutes at 165°C (329°F)
Specific Gravity	1.22
Durometer, Type A	70
Tensile Strength	1,325 psi (9.1 MPa)
Elongation	465%
Tear Strength	240 ppi (42.3 kN/m)
Stress at 200% Strain	825 psi (5.7 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

†(Performed using a SEMCO® model 250-A pneumatic gun with a ⅛ nozzle orifice and 90± 5 psi air pressure)

Full details » MED-4970 Product Profile

MED-4971 » High Clarity Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Extrusion Rate†, Part A	80 g/min
Extrusion Rate†, Part B	85 g/min
Work Time	>72 hours
Cured: 15 ± 0.5 minutes at 150 ± 5°C
Specific Gravity	1.16
Durometer, Type A	68
Tensile Strength	875 psi (MPa)
Elongation	230%
Tear Strength	170 ppi (kN/m)
Stress at 100% Strain	580 psi (MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

†(Performed using a SEMCO® model 250-A pneumatic gun with a ⅛ nozzle orifice and 90± 5 psi air pressure)

Full details » MED-4971 Product Profile

MED-4980 » Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Extrusion Rate†, Part A	35 g/min
Extrusion Rate†, Part B	180 g/min
Work Time	>24 hours
Cured: 5 minutes at 165°C (329°F)
Specific Gravity	1.17
Durometer, Type A	80
Tensile Strength	1000 psi (6.9 MPa)
Elongation	250%
Tear Strength	90 ppi (15.9 kN/m)
Stress at 100% Strain	865 psi (6.0 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

†(Performed using a SEMCO® model 250-A pneumatic gun with a ⅛ nozzle orifice and 90± 5 psi air pressure)

Full details » MED-4980 Product Profile

MED1-4955 » Self-lubricating Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Work Time	>72 hours
Cured: 5 minutes at 165°C (329°F). Stabilize for 3 hours minimum at ambient temperature and humidity.
Specific Gravity	1.14
Durometer, Type A	55
Tensile Strength	1,165 psi (8.0 MPa)
Elongation	490%
Tear Strength	250 ppi (44.1 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

Full details » MED1-4955 Product Profile

MED2-4955 » Self-lubricating Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Extrusion Rate†, Part A	214 g/min
Extrusion Rate†, Part B	260 g/min
Work Time	>72 hours
Cured: 5 minutes ate 165°C (329°F)
Specific Gravity	1.14
Durometer, Type A	61
Tensile Strength	1,200 psi (8.3 Mpa)
Elongation	490%
Tear Strength	250 ppi (44.1 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

†(Performed using a SEMCO® model 250-A pneumatic gun with a ⅛ nozzle orifice and 90± 5 psi air pressure)

Full details » MED2-4955 Product Profile

MED30-4940-1 » Self-lubricating Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Work Time	72 hours
Cured: 5 minutes at 150°C (302°C). Stabilize for 3 hours minimum at ambient temperature and humidity.
Specific Gravity	1.12
Durometer, Type A	35
Tensile Strength	970 psi (6.7 MPa)
Elongation	570%
Tear Strength	210 ppi (37.0 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

Full details » MED30-4940-1 Product Profile

MED50-5438 » Fluorosilicone Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Extrusion Rate†, Part A	90 g/min
Extrusion Rate†, Part B	140 g/min
Work Time	16 hours
Cured: 30 minutes at 150°C (302°F)
Specific Gravity	1.25
Durometer, Type A	31
Tensile Strength	650 psi (4.5 MPa)
Elongation	350%
Tear Strength	36 ppi (6.3 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

†(Performed using a SEMCO® model 250-A pneumatic gun with a ⅛ nozzle orifice and 90± 5 psi air pressure)

Full details » MED50-5438 Product Profile

Pressure Sensitive Adhesives

MED-1353 » Pressure Sensitive Silicone Adhesive

PROPERTIES
Typical Properties	Average Result
Uncured:
Viscosity	3.500 cP (3.500 mPas)
Appearance	Translucent
Non-Volatile Content	68%
Tack Test	2.8 lbs (12.2 N)
Cured: 24 hours minimum at ambient temperature and humidity. 15 minutes at 150°C (302°F)
180° Peel Strength	5.0 ppi (0.9 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-1353 Product Profile

MED-1356 » Pressure Sensitive Silicone Adhesive

PROPERTIES
Typical Properties	Average Result
Uncured:
Viscosity	1,750 cP (1,750 mPas)
Appearance	Translucent
Non-Volatile Content	65%
Tack Test	2.3 lbs (10.3 N)
Cured: 30 minutes at 70°C (158°F)
180° Peel Strength	3.0 ppi (0.5 kN/m)
Cured: 24 hours minimum at ambient temperature and humidity. 15 minutes at 150°C (302°F)
Tissue Culture (Cytotoxicity Testing)	Pass

# Also see: MED1-1356 for even better adhesion

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-1356 Product Profile

MED1-1356 » Pressure Sensitive Silicone Adhesive

PROPERTIES
Typical Properties	Average Result
Uncured:
Viscosity	300 cP (300 mPas)
Appearance	Translucent
Non-Volatile Content	50%
Tack Test	1.7 lbs (7.5 N)
Cured: 30 minutes at 70°C (158°F)
180° Peel Strength	3.75 ppi (0.7 kN/m)
Cured: 24 hours minimum at ambient temperature and humidity. 15 minutes at 150°C (302°F)
Tissue Culture (Cytotoxicity Testing)	Pass

# Also see: MED-1356

Full details » MED1-1356 Product Profile

Primers

MED-160 » Silicone Primer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Percent Solids	4.0%
Specific Gravity, Pycnometer	0.77
Devolatilized: 2 hours at ambient temperature and humidity
Tissue Culture (Cytotoxicity Testing)	Pass

Additional information for Primers: Application and Storage Recommendations PDF

Full details » MED-160 Product Profile

MED-162 » Silicone Primer For Polycarbonates

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Percent Solids	15%
Specific Gravity, Pycnometer	0.79
Cured: 2 hours minimum at ambient temperature and humidity
Tissue Culture (Cytotoxicity Testing)	Pass

Additional information for Primers: Application and Storage Recommendations PDF

Full details » MED-162 Product Profile

MED-163 » Silicone Primer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Specific Gravity, Pycnometer	0.78
Percent Solids	15%
Devolatilized: 2 hours minimum at ambient temperature and humidity
Tissue Culture (Cytotoxicity Testing)	Pass

Additional information for Primers: Application and Storage Recommendations PDF

Full details » MED-163 Product Profile

MED-164 » Silicone Primer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Transparent
Specific Gravity, Pycnometer	0.79
Percent Solids	10%
Devolatilized: 2 hours minimum at ambient temperature and humidity
Tissue Culture (Cytotoxicity Testing)	Pass

Additional information for Primers: Application and Storage Recommendations PDF

Full details » MED-164 Product Profile

MED-165 » Silicone Primer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Specific Gravity, Pycnometer	0.77
Percent Solids	4.5%
Devolatilized: 2 hours at ambient temperature and humidity
Tissue Culture (Cytotoxicity Testing)	Pass

Additional information for Primers: Application and Storage Recommendations PDF

Full details » MED-165 Product Profile

MED-166 » Silicone Primer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Specific Gravity, Pycnometer	0.8
Percent Solids	6.5%
Devolatilized: 1 hour minimum at ambient temperature and humidity
Tissue Culture (Cytotoxicity Testing)	Pass

Additional information for Primers: Application and Storage Recommendations PDF

Full details » MED-166 Product Profile

MED1-161 » Silicone Primer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Specific Gravity, Pycnometer	0.77
Percent Solids	4.5%
Devolatilized: 2 hours minimum at ambient temperature and humidity
Tissue Culture (Cytotoxicity Testing)	Pass

Additional information for Primers: Application and Storage Recommendations PDF

Full details » MED1-161 Product Profile

MED2-161 » Silicone Primer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Specific Gravity, Pycnometer	0.77
Percent Solids	4.5%
Devolatilized: 2 hours minimum at ambient temperature and humidity
Tissue Culture (Cytotoxicity Testing)	Pass

Additional information for Primers: Application and Storage Recommendations PDF

Full details » MED2-161 Product Profile

MED6-161 » Silicone Primer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Specific Gravity, Pycnometer	0.78
Percent Solids	9.0%
Devolatilized: 2 hours minimum at ambient temperature and humidity
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Additional information for Primers: Application and Storage Recommendations PDF

Full details » MED6-161 Product Profile

Simethicones

Soft Skin Adhesives

MED-6342 » Tacky Silicone Gel

NuSil Technology's MED-6342 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Work time	2 hours
Cured: 45 minutes at 135°C (275°F)
Penetration (62.4g cone, 60 seconds)	12 mm
Surface - Tack Test	10.0 psi
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-6342 Product Profile

MED-6345 » Tacky Silicone Gel

NuSil Technology's MED-6345 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Viscosity	16,000 cP (16,000 mPas)
Appearance	Translucent
Work Time	30 minutes
Cured: 3 hours at 60°C (140°F)
Penetration (62.4g cone, 60 seconds)	16.5 mm
Surface - Tack Test	5.0 psi
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-6345 Product Profile

MED-6346 » Silicone Gel

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Viscosity	7000 cP (7000 mPas)
Cure Time	5 minutes
Cured: 2 hours at 60°C
Surface-Tack Test	8 psi (0.06 MPa)
Penetration (¼" / 19.5 g for 5 seconds)	5.5 mm
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-6346 Product Profile

MED-6350 » Tacky Silicone Gel

NuSil Technology's MED-6350 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Viscosity	23,000 cP (23,000 mPas)
Appearance	Translucent
Work Time	2.5 hours
Cured: 30 minutes at 100°C (212°F)
Penetration (62.4g cone, 60 seconds)	13.9 mm
Surface - Tack Test	6.5 psi
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-6350 Product Profile

MED-6360 » Soft Silicone Adhesive

NuSil Technology's MED-6350 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Viscosity	465 cP (465 mPas)
Appearance	Translucent
Work Time	1 hour
Cured: 60 minutes at 140°C (284°F)
Penetration (62.4g cone, 60 seconds)	12 mm
Surface - Tack Test	12.0 psi
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-6360 Product Profile

MED-6362 » Soft Silicone Adhesive

NuSil Technology's MED-6362 shall not be considered for use in human implantation for a period of greater than 29 days.

PROPERTIES
Typical Properties	Average Result
Uncured:
Viscosity	8,500 cP (8,800 mPas)
Appearance	Translucent
Work Time	1 hour
Cured: 60 minutes at 140°C (284°F)
Penetration (62.4g cone, 60 seconds)	13 mm
Surface - Tack Test	9.0 psi
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-6362 Product Profile

Specialty Dispersions

MED-4159 » Silicone Dispersion

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Transparent
Non-Volatile Content	53%
Viscosity	185 cSt (159 mPas)
Cured: 7 days minimum at ambient temperature and humidity
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4159 Product Profile

MED-4162 » Silicone Dispersion

PROPERTIES
Typical Properties	Average Result
Appearance	Translucent
Non-Volatile Content	31%
Viscosity	30,000 cP (30,000 mPas)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4162 Product Profile

MED10-4161 » Silicone Dispersion

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Clear to amber
Non-Volatile Content	33%
Specific Gravity, Pycnometer	0.86
Viscosity	150 cSt (129 mPas)
Cured: 5 days minimum at 25°C (77°F), 50% relative humidity
Durometer, Type 00	25
Tissue Culture (Cytotoxicity Testing)	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED10-4161 Product Profile

MED10-6670 » Low Coefficient Of Friction Silicone Coating

PROPERTIES
Typical Properties	Average Result
Uncured:.
Appearance A	Translucent
Appearance B	Translucent to White
Zahn cup Viscosity, Cup #2	16 seconds
Percent Solids, Mixed	25%
Cured: 5 minutes minimum at ambient temperature and humidity, then 5 minutes at 150°C (302°F)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED10-6670 Product Profile

Specialty Liquid Silicone Rubbers

MED-4971 » High Clarity Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Extrusion Rate†, Part A	80 g/min
Extrusion Rate†, Part B	85 g/min
Work Time	>72 hours
Cured: 15 ± 0.5 minutes at 150 ± 5°C
Specific Gravity	1.16
Durometer, Type A	68
Tensile Strength	875 psi (MPa)
Elongation	230%
Tear Strength	170 ppi (kN/m)
Stress at 100% Strain	580 psi (MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

†(Performed using a SEMCO® model 250-A pneumatic gun with a ⅛ nozzle orifice and 90± 5 psi air pressure)

Full details » MED-4971 Product Profile

MED1-4955 » Self-lubricating Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Work Time	>72 hours
Cured: 5 minutes at 165°C (329°F). Stabilize for 3 hours minimum at ambient temperature and humidity.
Specific Gravity	1.14
Durometer, Type A	55
Tensile Strength	1,165 psi (8.0 MPa)
Elongation	490%
Tear Strength	250 ppi (44.1 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

Full details » MED1-4955 Product Profile

MED2-4955 » Self-lubricating Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Extrusion Rate†, Part A	214 g/min
Extrusion Rate†, Part B	260 g/min
Work Time	>72 hours
Cured: 5 minutes ate 165°C (329°F)
Specific Gravity	1.14
Durometer, Type A	61
Tensile Strength	1,200 psi (8.3 Mpa)
Elongation	490%
Tear Strength	250 ppi (44.1 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

†(Performed using a SEMCO® model 250-A pneumatic gun with a ⅛ nozzle orifice and 90± 5 psi air pressure)

Full details » MED2-4955 Product Profile

MED30-4940-1 » Self-lubricating Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Work Time	72 hours
Cured: 5 minutes at 150°C (302°C). Stabilize for 3 hours minimum at ambient temperature and humidity.
Specific Gravity	1.12
Durometer, Type A	35
Tensile Strength	970 psi (6.7 MPa)
Elongation	570%
Tear Strength	210 ppi (37.0 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

Full details » MED30-4940-1 Product Profile

MED50-5438 » Fluorosilicone Liquid Silicone Rubber

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Extrusion Rate†, Part A	90 g/min
Extrusion Rate†, Part B	140 g/min
Work Time	16 hours
Cured: 30 minutes at 150°C (302°F)
Specific Gravity	1.25
Durometer, Type A	31
Tensile Strength	650 psi (4.5 MPa)
Elongation	350%
Tear Strength	36 ppi (6.3 kN/m)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

†(Performed using a SEMCO® model 250-A pneumatic gun with a ⅛ nozzle orifice and 90± 5 psi air pressure)

Full details » MED50-5438 Product Profile

Ultra High Performance

MED-4027 » UHP High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Work Time (Pot Life) @ 25°C	2.5 hours
Cured: 10 minutes at 171°C (340°F). Stabilize for 24 hours minimum at ambient temperature and humidity.
Specific Gravity	1.11
Durometer, Type A	30
Tensile Strength	2,300 psi (15.9 MPa)
Elongation	1050%
Tear Strength	235 ppi (41.2 kN/m)
Stress at 200% Strain	100 psi (0.69 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4027 Product Profile

MED-4055 » UHP High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Plasticity, Part A	85 mils (2.2 mm)
Plasticity, Part B	75 mils (1.9 mm)
Work Time	2.5 hours
Cured: 10 minutes at 138°C (280°F)
Specific Gravity	1.14
Post-Cured: 4 hours at 177°C (351°F). Stabilize for 24 hours minimum at ambient temperature and humidity.
Durometer, Type A	55
Tensile Strength	1,655 psi (11.4 MPa)
Elongation	880%
Tear Strength	315 ppi (55.6 kN/m)
Stress at 200% Strain	490 psi (3.4 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4055 Product Profile

MED-4070 » UHP High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Average Result
Uncured:
Appearance	Translucent
Plasticity, Part A	120 mils (3.0 mm)
Plasticity, Part B	110 mils (2.8 mm)
Work Time	2.0 hours
Cured: 10 minutes at 138°C (280°F)
Specific Gravity	1.19
Post-Cured: 4 hours at 177°C (351°F). Stabilize for 24 hours minimum at ambient temperature and humidity.
Durometer, Type A	70
Tensile Strength	1,430 psi (9.9 MPa)
Elongation	760%
Tear Strength	300 ppi (52.9 kN/m)
Stress at 200% Strain	595 psi (4.1 MPa)
Tissue Culture (Cytotoxicity Testing)	Pass
Elemental Analysis of Trace Metals	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4070 Product Profile

VersaSil

MED-4032 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Versasil³ 30 Med-4032	Versasil³ 40 Med-4042	Versasil³ 50 Med-4052
Cured: 10 min. at 116°C (241°F)
Specific Gravity	1.1	1.11	1.16
Durometer, Type A	30	40	50
Tensile Strength	1,200 psi (8.3 MPa)	1,475 psi (10.2 MPa)	1,400 psi (9.7 MPa)
Elongation	1,100%	1,000%	1,100%
Tear Strength	160 ppi (28.2 kN/m)	160 ppi (28.2 kN/m)	230 ppi (40.6 kN/m)
Stress at 200% Strain	140 psi (1.0 MPa)	230 psi (1.6 MPa)	280 psi (1.9 MPa)
Tissue Culture (Cytotocixity Testing)	Pass	Pass	Pass
Elemental Analysis of Trace Metals	Pass	Pass	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4032 Product Profile

MED-4042 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Versasil³ 30 Med-4032	Versasil³ 40 Med-4042	Versasil³ 50 Med-4052
Cured: 10 min. at 116°C (241°F)
Specific Gravity	1.1	1.11	1.16
Durometer, Type A	30	40	50
Tensile Strength	1,200 psi (8.3 MPa)	1,475 psi (10.2 MPa)	1,400 psi (9.7 MPa)
Elongation	1,100%	1,000%	1,100%
Tear Strength	160 ppi (28.2 kN/m)	160 ppi (28.2 kN/m)	230 ppi (40.6 kN/m)
Stress at 200% Strain	140 psi (1.0 MPa)	230 psi (1.6 MPa)	280 psi (1.9 MPa)
Tissue Culture (Cytotocixity Testing)	Pass	Pass	Pass
Elemental Analysis of Trace Metals	Pass	Pass	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4042 Product Profile

MED-4052 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Versasil³ 30 Med-4032	Versasil³ 40 Med-4042	Versasil³ 50 Med-4052
Cured: 10 min. at 116°C (241°F)
Specific Gravity	1.1	1.11	1.16
Durometer, Type A	30	40	50
Tensile Strength	1,200 psi (8.3 MPa)	1,475 psi (10.2 MPa)	1,400 psi (9.7 MPa)
Elongation	1,100%	1,000%	1,100%
Tear Strength	160 ppi (28.2 kN/m)	160 ppi (28.2 kN/m)	230 ppi (40.6 kN/m)
Stress at 200% Strain	140 psi (1.0 MPa)	230 psi (1.6 MPa)	280 psi (1.9 MPa)
Tissue Culture (Cytotocixity Testing)	Pass	Pass	Pass
Elemental Analysis of Trace Metals	Pass	Pass	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4052 Product Profile

MED-4062 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Versasil³ 30 Med-4032	Versasil³ 40 Med-4042	Versasil³ 50 Med-4052	Versasil³ 50 Med-4062
Cured: 10 min. at 116°C (241°F)
Specific Gravity	1.1	1.11	1.16	1.16
Durometer, Type A	30	40	50	60
Tensile Strength	1,200 psi (8.3 MPa)	1,475 psi (10.2 MPa)	1,400 psi (9.7 MPa)	1,400 psi (9.7 MPa)
Elongation	1,100%	1,000%	1,100%	1,000%
Tear Strength	160 ppi (28.2 kN/m)	160 ppi (28.2 kN/m)	230 ppi (40.6 kN/m)	250 ppi (44.1 kN/m)
Stress at 200% Strain	140 psi (1.0 MPa)	230 psi (1.6 MPa)	280 psi (1.9 MPa)	300 psi (2.1 MPa)
Tissue Culture (Cytotocixity Testing)	Pass	Pass	Pass	Pass
Elemental Analysis of Trace Metals	Pass	Pass	Pass	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4062 Product Profile

MED-4072 » High Consistency Silicone Elastomer

PROPERTIES
Typical Properties	Versasil³ 30 Med-4032	Versasil³ 40 Med-4042	Versasil³ 50 Med-4052
Cured: 10 min. at 116°C (241°F)
Specific Gravity	1.1	1.11	1.16
Durometer, Type A	30	40	50
Tensile Strength	1,200 psi (8.3 MPa)	1,475 psi (10.2 MPa)	1,400 psi (9.7 MPa)
Elongation	1,100%	1,000%	1,100%
Tear Strength	160 ppi (28.2 kN/m)	160 ppi (28.2 kN/m)	230 ppi (40.6 kN/m)
Stress at 200% Strain	140 psi (1.0 MPa)	230 psi (1.6 MPa)	280 psi (1.9 MPa)
Tissue Culture (Cytotocixity Testing)	Pass	Pass	Pass
Elemental Analysis of Trace Metals	Pass	Pass	Pass
Cured: 10 min. at 116°C (241°F)
Specific Gravity	1.16	1.22	1.22
Durometer, Type A	60	70	80
Tensile Strength	1,400 psi (9.7 MPa)	1,100 psi (7.6 MPa)	1,150 psi (7.9 MPa)
Elongation	1,000%	875%	900%
Tear Strength	250 ppi (44.1 kN/m)	240 ppi (42.3 kN/m)	200 ppi (35.5 kN/m)
Stress at 200% Strain	300 psi (2.1 MPa)	450 psi (3.1 MPa)	400 psi (2.8MPa)
Tissue Culture (Cytotocixity Testing)	Pass	Pass	Pass
Elemental Analysis of Trace Metals	Pass	Pass	Pass

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Full details » MED-4072 Product Profile

MED-4082 » High Consistency Silicone Elastomer

PROPERTIES
TYPICAL PROPERTIES	AVERAGE RESULT	STANDARD	NT-TM
Cured: 10 min. @ 116°C (241°F). Stabilize for 3 hours minimum at ambient temperature and humidity
Specific Gravity	1.22	ASTM D792	003
Durometer, Type A	80	ASTM D2240	006
Tensile Strength	1,150 psi (7.9 MPa)	ASTM D412	007
Elongation	900%	ASTM D412	007
Tear Strength	200 ppi (35.5 kN/m)	ASTM D624	009
Stress @ 200% Strain	400 psi (2.8MPa)	ASTM D412	007
Tissue Culture (Cytotoxicity Testing)	Pass	USP <87> ISO 10993-5	061
Elemental Analysis of Trace Metals	Pass	ASTM E305	131

The data above represents the properties of the product when cured using the Addition Cure System (CAT-40 and CAT-55).

These properties tested on a lot-to-lot basis. Please contact NuSil Technology for assistance and recommendations in establishing particular specifications.

Polymer Systems Technology Limited

Biomaterials

General Healthcare

Adhesives

MED-1000 » Silicone Adhesive

MED-1011 » Silicone Adhesive

MED-1031 » Silicone Adhesive

MED-1037 » Silicone Adhesive

MED-1040 » Rtv Silicone Adhesive

MED-1353 » Pressure Sensitive Silicone Adhesive

MED-1356 » Pressure Sensitive Silicone Adhesive

MED-6342 » Tacky Silicone Gel

MED-6345 » Tacky Silicone Gel

MED-6346 » Silicone Gel

MED-6350 » Tacky Silicone Gel

MED-6360 » Soft Silicone Adhesive

MED-6362 » Soft Silicone Adhesive

MED1-1356 » Pressure Sensitive Silicone Adhesive

MED1-4013 » Fast-Cure Silicone Adhesives

MED2-4013 » Fast-Cure Silicone Adhesives

MED3-4013 » Fast-Cure Silicone Adhesives

Color Masterbatches

MED-4102 » OVERVIEW Color Masterbatch For High Consistency Silicone Elastomer

MED-4102-1 » Color Masterbatch For High Consistency Silicone Elastomer ‑ White

MED-4102-2 » Color Masterbatch For High Consistency Silicone Elastomer ‑ Black

MED-4102-3 » Color Masterbatch For High Consistency Silicone Elastomer ‑ Red

MED-4102-4 » Color Masterbatch For High Consistency Silicone Elastomer ‑ Orange

MED-4102-5 » Color Masterbatch For High Consistency Silicone Elastomer ‑ Yellow

MED-4102-6 » Color Masterbatch For High Consistency Silicone Elastomer ‑ Dark Green

MED-4102-7 » Color Masterbatch For High Consistency Silicone Elastomer ‑ Dark Blue

MED-4900 » OVERVIEW Color Masterbatch For Liquid Silicone Elastomer

MED-4900-1 » Color Masterbatch For Liquid Silicone Elastomer ‑ White

MED-4900-2 » Color Masterbatch For Liquid Silicone Elastomer ‑ Black

MED-4900-3 » Color Masterbatch For Liquid Silicone Elastomer ‑ Red

MED-4900-4 » Color Masterbatch For Liquid Silicone Elastomer ‑ Orange

MED-4900-5 » Color Masterbatch For Liquid Silicone Elastomer ‑ Yellow

MED-4900-6 » Color Masterbatch For Liquid Silicone Elastomer ‑ Dark Green

MED-4900-7 » Color Masterbatch For Liquid Silicone Elastomer ‑ Dark Blue

MED2-4102-6 » Color Masterbatch For High Consistency Silicone Elastomer ‑ Light Green

MED2-4900 » Barium Sulfate Healthcare Silicone Color Masterbatch ‑ White

MED2-4900-6 » Color Masterbatch For Liquid Silicone Elastomer ‑ Light Green

MED3-4900 » Titanium Dioxide Healthcare Silicone Color Masterbatch ‑ White

MED3-4900-8 » Color Masterbatch For Liquid Silicone Elastomer ‑ Violet

MED4-4900 » Ammonium Bicarbonate Healthcare Silicone Foam Color Masterbatch ‑ White

MED50-4900-1 » Color Masterbatches For Liquid Silicone Elastomer ‑ Translucent White

MED50-4900-2 » Color Masterbatches For Liquid Silicone Elastomer ‑ Translucent Black

MED50-4900-3 » Color Masterbatches For Liquid Silicone Elastomer ‑ Translucent Red

MED50-4900-4 » Color Masterbatches For Liquid Silicone Elastomer ‑ Translucent Orange

MED50-4900-5 » Color Masterbatches For Liquid Silicone Elastomer ‑ Translucent Yellow

MED50-4900-6 » Color Masterbatches For Liquid Silicone Elastomer ‑ Translucent Dark Green

MED50-4900-7 » Color Masterbatches For Liquid Silicone Elastomer ‑ Translucent Dark Blue

MED52-4900-6 » Color Masterbatches For Liquid Silicone Elastomer ‑ Translucent Light Green

MED53-4900-7 » Color Masterbatches For Liquid Silicone Elastomer ‑ Translucent Violet

Dispersions

MED-2014 » Silicone Dispersion

MED-4159 » Silicone Dispersion

MED-4162 » Silicone Dispersion

MED10-4161 » Silicone Dispersion

MED10-6400 » Addition Cure Silicone Dispersion

MED10-6600 » Addition Cure Silicone Dispersion

MED10-6605 » Rtv Cure Silicone Dispersion

MED10-6607 » Rtv Silicone Dispersion

MED10-6640 » Addition Cure High Strength Silicone Dispersion

MED10-6655 » Rtv Fluorosilicone Dispersion

MED10-6670 » Low Coefficient Of Friction Silicone Coating

MED11-6604 » Rtv Silicone Dispersion

MED16-6606 » Rtv Silicone Dispersion

Fluids

MED-361 » Silicone Fluid

MED-400 » Silicone Fluid

MED-420 » Silicone Fluid

MED-460 » Silicone Fluid

Greases

MED-6731 » High Consistency Fluorosilicone Grease

MED-9011 » Low Consistency Silicone Grease

MED-9021 » Medium Consistency Silicone Grease

MED-9031 » High Consistency Silicone Grease

Polymer Systems
Technology Limited